tag:blogger.com,1999:blog-3712577241932959808.post1486337477262390890..comments2024-01-30T02:01:51.326-06:00Comments on Integration Yay!: DataPower: Static routes and management interface Bruno R Neveshttp://www.blogger.com/profile/06753136071159835651noreply@blogger.comBlogger5125tag:blogger.com,1999:blog-3712577241932959808.post-64986049184296542952015-12-02T10:31:30.693-06:002015-12-02T10:31:30.693-06:00Good catch! That was probably something I forgot t...Good catch! That was probably something I forgot to fix while editing the post, can't remember of my thought now back then. It is updated now, I kept the "or". Thank you!Bruno R Neveshttps://www.blogger.com/profile/06753136071159835651noreply@blogger.comtag:blogger.com,1999:blog-3712577241932959808.post-43485173420056347792015-12-01T15:05:09.882-06:002015-12-01T15:05:09.882-06:00[if you are not on the same subnet of the device (...[if you are not on the same subnet of the device (/24) or/and the management service is not configured for all network interfaces (0.0.0.0)]<br /><br />Why this point is "or/and" ?Unknownhttps://www.blogger.com/profile/03806276441593448345noreply@blogger.comtag:blogger.com,1999:blog-3712577241932959808.post-6726800539065614692015-04-16T14:11:50.930-05:002015-04-16T14:11:50.930-05:00Hey Hydro, to remove the default gateway using the...Hey Hydro, to remove the default gateway using the CLI, you can try the following:<br /><br />xi50# co<br />Global configuration mode<br /><br />xi50(config)# interface mgt0<br />Interface configuration mode (mgt0 )<br /><br />xi50(config-if[eth4])# show default-gateway<br />default IPv4 gateway: 192.168.10.254<br />default IPv6 gateway: (none)<br /><br />xi50(config-if[eth4])# no ip default-gateway<br />Operation succeeded<br /><br />xi50(config-if[eth4])# show default-gateway <br />default IPv4 gateway: (none)<br />default IPv6 gateway: (none)<br /><br />Before applying these commands, make sure you have connectivity with the appliance through other interfaces or by being in the same subnet. I don't want you to lose access to it (it is explained in detail in this article how to avoid that). But as long as you have access to it through the serial interface for example, you should be safe to play with it as much as you want.Bruno R Neveshttps://www.blogger.com/profile/06753136071159835651noreply@blogger.comtag:blogger.com,1999:blog-3712577241932959808.post-56908255144196668142015-04-16T01:42:50.564-05:002015-04-16T01:42:50.564-05:00How to remove the default gateway
i tried the com...How to remove the default gateway<br /><br />i tried the command no ip route but i am getting the below error<br /><br />% Subnet Route Removal failed, because subnet route was not found.Hydrohttps://www.blogger.com/profile/04867864168975035688noreply@blogger.comtag:blogger.com,1999:blog-3712577241932959808.post-11519080167336229322014-09-19T06:47:51.504-05:002014-09-19T06:47:51.504-05:00great!great!BolingaPelusahttps://www.blogger.com/profile/04654963306973237901noreply@blogger.com